Hardware Kit for the Curt Lunette Ring - Flat Plate Mount

Question

Question:

Curt Lunette Ring - Flat Plate Mount - 3 Diameter - 60,000 lbs - C48560 What is the recommended hardware to install this Lunette Ring?

asked by: Eduardo E

0

Expert Reply:

To mount the Curt Lunette Ring - Flat Plate Mount - 3" Diameter - 60,000 lbs, part # C48560, you can use the Lunette Ring Hardware Kit - Flush Mount, part # C48KR. It includes four 3/4" hex bolts, four nylock nuts and four flat washers.

I've linked to a video review of the lunette ring for your reference.

expert reply by: Kef G

0

Answer 1

The difference between the two tire weight ratings for the part #TTWTRTM2358016E is for a setup that has a dually style axle where there is 2 wheels per side of axle for a total of 4 wheels per axle. I spoke with our local tire guru here at…

view full answer...

Answer 2

I recommend going with the Provider 215/75R17.5 Radial Trailer Tire #TTWP15175 as it is the best tire we have in that size. The Provider uses a better siping pattern than the other options so that you get the best traction whether it is wet or dry…

view full answer...

Answer 3

The tire capacity difference for single and dual wheel setups is for dually and single wheel axles. It's not the difference between tandem axle and single axle trailers. For example compare these capacities for a tire: Single tire: 3,420 lbs…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The mounting bolt pattern for the Buyers Products 3" I.D. Heavy-Duty Forged 4-Bolt Mount Lunette Ring #337BDB1385 that you referenced is 4-1/2 inches square.

view full answer...

Answer 7

The Demco coupler #DM12662-97 is fairly shallow front to back. Because of that you are going to want to weld it everywhere that it makes contact with the trailer tongue especially considering the capacities involved. That would be the back side and…

view full answer...

Answer 8

We have several 3-inch lunette ring (pintle eye) couplers that are shown on the linked page. These are offered with and without a channel mount, such as #T1812800 and #T1613700, respectively. I went to our warehouse and measured the hole size and…

view full answer...

Answer 9

The main reason people like oil bath hubs over grease hubs is the oil bath hubs have a less involved maintenance schedule than grease hubs. It is recommended to inspect and repack grease wheel bearings and seals every 12k miles. With oil bath hubs,…

view full answer...

Answer 10

Yes, you can install the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1020 with the BedRug Custom Truck Bed Mat #BR44FR on your 2022 GMC Sierra 2500 with the 6-3/4' bed. You will need to make cutouts in the BedRug though for…

view full answer...

Answer 11

For the Lippert 4,000 lb axle trailer hubs the bearings are #25580 for the inner bearing and #LM67048 for the outer. So for a kit that has both you'd want the #BK3-310. Then for self adjusting brake assemblies you could use the part…

view full answer...

Hardware Kit for the Curt Lunette Ring - Flat Plate Mount

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching