Replacement Cover and Cap for etrailer and Ram Electric A-Frame Jacks

Question

Question:

I need a Replacement Cover for etrailer and Ram Electric A-Frame Jacks - White but I don’t see the correct plug or cap for this replacement. Does lithe part I’m referring to come with it or how can I get it too

asked by: Dan

0

Expert Reply:

The Replacement Cover for etrailer and Ram Electric A-Frame Jacks - White, part # EJ-3520-CVRW, does not come with the cap. It is only the housing portion.

If you need the cap as well, the replacement for that is part # EJ-3520-BCP.

expert reply by: Kef G

0

Answer 1

First, we need to determine the axle capacities and gross trailer weight (GTW) capacity of your 24 foot Wells Fargo trailer. The reason axle and GTW capacity is important is if you upgrade the tires or tires and wheels to handle more capacity, you…

view full answer...

Answer 2

Is there any other info on the tire you can find? The numbers you mentioned are not the size so I am not able to determine what you'd need at this time.

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Cover and Cap for etrailer and Ram Electric A-Frame Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching