Recommended Footplate For Bulldog Fulton Sidewind 14 5000LB A-Frame Jack

Question

Question:

will this fit my bulldog fulton sidewind 14 travel a-frame jack 5000-pound?

asked by: Tom E

0

Expert Reply:

I have another option but the Replacement Foot for etrailer or Ram Electric Jacks # EJ-3520-FT you were looking at will not work on your jack as it was designed to be use with the # EJ-3520-BBX or # EJ-3520-WBX.

Since your Bulldog Fulton Sidewind 14 5000lb A-Frame Jack uses a 2" tube you can use the Bulldog Detachable Footplate for 2" Jack Tube # BD018564 which is rated up to 5000lbs.

I included a video of the Bulldog # BD018564 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

I have not seen any additional add on parts for the Fastway Flip Automatic Fold-Up Jack Foot #FA88-00-4500 that will do what you are looking for. And it can be used on a pop up that is using a 2-1/4" tongue jack. I recommend the Roadmaster Quick…

view full answer...

Answer 2

While we do not carry just the tube for your 2017 Jayco White Hawk Travel Trailer's electric jack, we do carry other replacement parts for the jack and full-on replacement jacks. As a full replacement, the etrailer Electric Jack - A-Frame, part…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The outer diameter of this tube is 1-3/4 inches, if that matches the diameter of your old foot, this should work well for you. A snapper pin like #2500-26 is typically used to hold the foot in place.

view full answer...

Answer 6

Yes the Pro Series A-frame jack part #PSRV20000103 will work great as a replacement for the powered Atwood jack you have now on your trailer. It will easily bolt up in place of it and would have more than enough lifting capacity for your trailer that…

view full answer...

Answer 7

It won't because the grove in the leg is different enough that they aren't compatible, however I have another option that will. It is the Replacement Drop Leg for Bulldog Round Trailer Jack or Powered Drive Camper Jack item #BD500190. This is…

view full answer...

Answer 8

Yes, I checked with TorkLift and can confirm the correct set of TorkLift Custom Frame-Mounted Camper Tie-Downs for your 2019 Toyota Tundra Double Cab with 6-1/2' bed, Factory Hitch, and Running Boards (Stop at Cab) is part #TLT3306 for the rear…

view full answer...

Answer 9

The inner diameter of the #Foot Pad #2500-25 is approximately 1-11/16 inches.

view full answer...

Answer 10

We have the A-frame tool box part #UWS01039 which would be tall enough for a propane tank that is 19 inches tall but the #313-TM362016M would be just a little bit too short for that. I attached a review video for more info on this for you to check…

view full answer...

Answer 11

While we do not have a video showing the installation of the line relocation kit that comes with the SumoSprings Trailer Helper Springs #TSS-107-40, I have linked a video below that shows an example of when one will be needed and explains what the…

view full answer...

Recommended Footplate For Bulldog Fulton Sidewind 14 5000LB A-Frame Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching