Recommended Replacement Drop Leg for a Bulldog Tongue Jack

Question

Question:

I need an extension leg for my 2022 Featherlite trailer with 2000# Bull Dog tongue jack the OD of the leg is 2inch and your part# EJ-3520-FT looks like it is what I need. Will this fit?

asked by: Vern S

0

Expert Reply:

It won't because the grove in the leg is different enough that they aren't compatible, however I have another option that will. It is the Replacement Drop Leg for Bulldog Round Trailer Jack or Powered Drive Camper Jack item # BD500190. This is an exact replacement part.

The Replacement Foot for etrailer or Ram Electric Jacks item # EJ-3520-FT you were looking at will not work on your jack as it was designed to be use with the item # EJ-3520-BBX or item # EJ-3520-WBX jacks.

expert reply by: Jerred H

0

Answer 1

While we do not have a video showing the installation of the line relocation kit that comes with the SumoSprings Trailer Helper Springs #TSS-107-40, I have linked a video below that shows an example of when one will be needed and explains what the…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 4

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear to…

view full answer...

Answer 5

The AllTrek 4000 kits provide the best cushioning so if you were to upgrade from your CRE3000 kit to the Alltrek you would see a big improvement. If you have a 35 inch wheelbase you'd want the part #MR29DR or if you have a 33 inch wheelbase…

view full answer...

Answer 6

The brackets on the SumoSprings Trailer Helper Springs #SS26MV are 1-1/2" wide so they will fit evenly across the humps on your spring pads. I do not recommend cutting down the spring and you will be able to use these even with only having…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Jeremy; that's a good question and you'll actually need to go ahead and re-do the set up of your weight distribution system after adding the Timbren Rear Suspension Enhancement System #TDR1500DS to your 2019 Ram 1500. So it wouldn't…

view full answer...

Answer 9

Hello Jim. For you I Recommend the SumoSprings Solo Custom Helper Springs #SS47PV. These are 1,800 lb capacity urethane jounce springs which will replace the factory bumpstops. I like these for a few reasons. The 1,800 lb capacity will be enough to…

view full answer...

Answer 10

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle tube to…

view full answer...

Answer 11

For your 2022 Grand Design 22RBE with dual 3,500 lb overslung dexter axles the correct SumoSpring kit is part #TSS-107-40. Since your trailer is a tandem axle you will need two of these kits. These are made specifically for overslung axles rated…

view full answer...

Recommended Replacement Drop Leg for a Bulldog Tongue Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching