Where To Place Valterra Folding Manual Stabilizer On 2017 Winnebago 24G Class C Motorhome

Question

Question:

Where to place them on 2017 winnebago 24g motor coach ?

asked by: Eric W

1

Helpful Expert Reply:

The best area to place the Valterra Folding Manual Stabilizer for Trailers and RVs # 020106 is underneath the rear bumper or frame rails closest to the rear bumper, and under the frame on the side of your 2017 Winnebago 24G Class C Motorhome where the entry door is.

The Valterra # 020106 will work on any RV or Trailer that has between 14"-28" of frame to ground clearance.

expert reply by: Samuel C

1

Answer 1

Because it's lighter, less expensive, has fewer moving parts and is mechanically less complicated I'd recommend going with the Gen-Y #325-GH-8040 shock absorbing pin box versus a Trailair Flex Air like part #LC328492. The Trailair…

view full answer...

Answer 2

It sounds like you have a hydraulic leak somewhere or that you have a bad seal. Since it's only for your front jack legs what you'll need to do is check the hydraulic line for those legs and also check the seals for your system. You…

view full answer...

Answer 3

I have good news for you, the Lippert #LC177094 Replacement Cartridge Valve you'd looked at is indeed the correct replacement for your Level Up system.

view full answer...

Answer 4

Provided that you have the space and mount it properly you could mount a scissor jack such as #UF48-979032 any which way you want. You might be interested in a different type of stabilizer such as #UF39-941705 which is electric or #UF39-941704…

view full answer...

Answer 5

Thanks for the picture and additional information! I just heard back from my rep at Lippert and you are correct your Keystone Raptor does have a 1116 pin box. You will need the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box item #GY23FR. Your math…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57541 does take up the same space as the Curt 19419346 5th wheel bracket kit for your 2024 GMC Sierra 3500. The only way to remedy this is to use the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 12

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Where To Place Valterra Folding Manual Stabilizer On 2017 Winnebago 24G Class C Motorhome

Product Page this Question was Asked From

Continue Researching