How Does Gustafson RV Reading Light Wire Up

Question

Question:

My RV has red and white feed to the existing lighting fixture. The LED lighting fixture I purchased from E-Trailer has a white and a black lead. How should I connect the wires since the LED is polarity sensitive?

asked by: Dan P

0

Expert Reply:

The easy solution would be to connect the wiring of your RV for the lighting to the wiring of the Gustafson light part # 277-000334 and it's either not going to power on or will.

When LED lights are wired backwards they simply don't work without damage so there would be no reason to worry. The black wire of this light is the power wire and the white is ground.

expert reply by: Jameson C

0

Answer 1

The Gustafson RV Reading Light #277-000334 has a color temperature of 3,200 Kelvin, which means it will have a hue emitting something between a yellowish and whitish light. With that particular color temperature there are going to be some slight…

view full answer...

Answer 2

I spoke with my contact at Gustafson and she informed me that the #277-000334 puts out 226 Lumens at a distance of 1 foot.

view full answer...

Answer 3

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 4

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

How Does Gustafson RV Reading Light Wire Up

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching