Correct Custom Mounting Bracket Kit for SnowBear Snowplows On a 2007 Ford F-150

Question

Question:

I Have a 2007 Ford F150 XLT 4x4 WITH A 6 inch LIFT, Is this the kit I need for this truck ?? , The plow set up I have is a old manual plow . not a hydraulic SB397-105 And the crossmember - SB324-060. Thank you

asked by: JEFFERY L

0

Expert Reply:

The correct Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows for a 2007 Ford F-150 is part # SB397-105. If the plow uses the two point mounting then the bracket kit will be a fit.

expert reply by: Conner L

0

Answer 1

In order to use a Snowbear plow on the front of a 2004 Jeep Grand Cherokee Laredo you'll need to use the one that installs with a front hitch. So for the front hitch you'd need the part #C31048 and then for the plow you'd want…

view full answer...

Answer 2

You will not need to relocate the license plate holder on the front of your 2004 Jeep Grand Cherokee. Check out the picture I attached that shows this hitch installed on a similar vehicle as yours to show that the license plate bracket will not…

view full answer...

Answer 3

There is not a bracket kit that fits a Laredo model. You will need to use the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31048 and then use either 82x19 inch snowplow #SB324-080 or #SB324-081 for 84x22 inch snowplow.

view full answer...

Answer 4

Sight unseen, It would be pretty difficult to say if you'd be able to install the hitch with an existing grille guard. The Curt #C31048 front mounted receiver attaches to the underside of the frame members at the front of the vehicle, the…

view full answer...

Answer 5

I contacted SnowBear and the SNB-SB200 plow needs a bracket fit part #SB397-105 to fit the 2006 F-150. Since the snow plow is an older model it did not come with the cross member so you do need the cross member to attach the plow to the truck part…

view full answer...

Answer 6

I spoke with my contact in Technical Support at Curt Manufacturing, who tells me that their front mounted receiver would bolt to the underside of the front frame members and around the front stabilizer bar using with two of the connection points…

view full answer...

Answer 7

All of the snow plows we offer for the 2000 Jeep Grand Cherokee are designed to mount with custom mounting brackets rather than a front mount hitch. One great snow plow option for your Grand Cherokee is the SnowBear Winter Wolf Snowplow #SB324-166…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...