Snow Bear Plow Recommendation for Fitting 2004 Jeep Grand Cherokee Laredo

Question

Question:

does the 397-041 mount go on 2004 jeep grand cherokee laredo or is ther a different mount i can use .it says it wont fit the laredo

asked by: Vincent R

0

Expert Reply:

In order to use a Snowbear plow on the front of a 2004 Jeep Grand Cherokee Laredo you'll need to use the one that installs with a front hitch. So for the front hitch you'd need the part # C31048 and then for the plow you'd want the part # SB324-081.

expert reply by: Jameson C

0

Answer 1

I contacted SnowBear and the SNB-SB200 plow needs a bracket fit part #SB397-105 to fit the 2006 F-150. Since the snow plow is an older model it did not come with the cross member so you do need the cross member to attach the plow to the truck part…

view full answer...

Answer 2

You will not need to relocate the license plate holder on the front of your 2004 Jeep Grand Cherokee. Check out the picture I attached that shows this hitch installed on a similar vehicle as yours to show that the license plate bracket will not need…

view full answer...

Answer 3

There is not a bracket kit that fits a Laredo model. You will need to use the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31048 and then use either 82x19 inch snowplow #SB324-080 or #SB324-081 for 84x22 inch snowplow.

view full answer...

Answer 4

Sight unseen, It would be pretty difficult to say if you'd be able to install the hitch with an existing grille guard. The Curt #C31048 front mounted receiver attaches to the underside of the frame members at the front of the vehicle, the…

view full answer...

Answer 5

The correct Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows for a 2007 Ford F-150 is part #SB397-105. If the plow uses the two point mounting then the bracket kit will be a fit.

view full answer...

Answer 6

I spoke with my contact in Technical Support at Curt Manufacturing, who tells me that their front mounted receiver would bolt to the underside of the front frame members and around the front stabilizer bar using with two of the connection points…

view full answer...

Answer 7

All of the snow plows we offer for the 2000 Jeep Grand Cherokee are designed to mount with custom mounting brackets rather than a front mount hitch. One great snow plow option for your Grand Cherokee is the SnowBear Winter Wolf Snowplow #SB324-166…

view full answer...

Answer 8

Yes, the difference between the Detail K2 Snowplow #K2AVAL8422 and Detail K2 Elite Snowplow #K2AVAL8422ELT is the Elite has the electric actuator over the winch. The Elite also uses a chain connection to the blade while the basic K2 has a strap that…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

I checked with Curt and I can confirm that the Curt Front Mount Trailer Hitch item #C22NR does fit the 2022 Chevrolet Silverado 1500 LT with the diesel engine. The only picture we have is from the installation instructions and I have attached it…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I confirmed with Blue Ox that the Blue Ox Ascent Tow Bar #BX4370 is absolutely compatible with the Blue Ox Aftermarket Off-Road Bumper Adapter - 7/8" Pin #BX88357. I have added a link to a video review for you to check out well of the Blue Ox…

view full answer...

Snow Bear Plow Recommendation for Fitting 2004 Jeep Grand Cherokee Laredo

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching