Brake Controller for 2012 Chevy Suburban With Factory 7-Way

Question

Question:

I have a 2012 Chevy suburban 1500. I would like to use it to tow a dump trailer with electric brakes however I have no controller. I’m not sure what all I need. I do have a 7 pin plug harness already from the factory. Any help is greatly appreciated.

asked by: Cory

0

Expert Reply:

I have good news because since your 2012 Chevy Suburban already has the factory 7-way, you won't need anything but the brake controller and wiring harness which you will splice into the wires which are already run under the dash. If you take a look at the accompanying photo, you can see where the wires are on your Suburban.

As for the brake controller for your Suburban, I highly recommend the Brake EVN # TK63VR .

I love the I-Command because it is a great value due to its unique combination of quality and cost-effectiveness. The I-Command is going to give you smooth braking, is easy to use, and has a bright display that is simple to read and understand. For a combination of quality, reliability, and price, there really isn't a better option than the I-Command. To install the I-Command in your Suburban with the factory 7-way will need the Brake Control Harness # 20127.

I have added a link below to a video which shows the Prodigy P2 # 90885 being installed on a similar model year Chevy Suburban which you can use as a guide to install the I-Command.

To connect the wires on the Suburban to the Brake Control Harness # 20127, the only other thing you will need are Butt Connectors # 05731-5 and # DW05745-5.

expert reply by: Kyle S

0

click to enlarge

Answer 1

That will depend on the amount of brake axles your trailer has. . The 20 amp breaker like #9506P is for 1 and 2 axle brakes, and the 30 amp like part #38630 is for 3 and 4 axle brakes

view full answer...

Answer 2

When choosing tie-down straps like the BoatBuckle G2 Retractable Tie-Down Strap, #IMF14220, you will want to keep a few things in mind. Boat tie-downs are designed for normal highway driving. The purpose of most boat tie-downs is to strap the…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 7

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 8

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 9

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 10

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake…

view full answer...

Brake Controller for 2012 Chevy Suburban With Factory 7-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching