How Do You Attach Horse Trailer Side Pads # HTP60BK To The Horse Trailer

Question

Question:

How do attach this type of pad to the trailer?

asked by: David S

0

Expert Reply:

We carry Horse Trailer Pad Screws for attaching the horse trailer pads. The part number for the Trailer Horse Pad Screw (Qty 1) is PS-8. The pads are installed in the trailer with the screws directly through the pad and can be secured anywhere it is convenient to the trailer ribs or framing.

If you look at the product page of # HTP60BK there is a picture under the customer reviews that will show how the pads are attached to the trailer.

expert reply by: Robert G

0

Answer 1

Are the holes you are referring to threaded? If so then you could drill a 1/4" hole into one of our pads (see below) and then use a bolt to attach them to the wall. If the holes are not threaded then it may just be best to use a few phillips…

view full answer...

Answer 2

The best option we have for your horse trailer is the Ribbed Rubber Trailer Mat part #3622RM for 36" wide x 22' long or part #4872SM for 48" wide x 72" long. These mats can then be cut to fit the exact size of your horse…

view full answer...

Answer 3

There is not a specific method for attaching the Horse Trailer Side Pad, #HTP60BK, to the trailer wall. You can use the Trailer Horse Pad Screw, #PS-8, but like you said it will puncture the material. Another option you have is to apply adhesive to…

view full answer...

Answer 4

The holes to attach the Horse Trailer Side Pad part #HTP60BK do need to be drilled but that is standard from the other horse trailer side pads I have researched. We do not carry the screws by the box but the screws that we recommend can be purchased…

view full answer...

Answer 5

In order to install the the Horse Trailer Side Pad - 60" #HTP1260BK you just need to screw them in. What you'll need are the Trailer Horse Pad Screw #PS-8 and attach them to the sides of the pad.

view full answer...

Answer 6

For the installation of your 60-inch horse trailer side pads, I recommend using the Trailer Horse Pad Screw #PS-8. The pads are installed in the trailer directly via the screws and can be mounted wherever is convenient. I have included a photo from…

view full answer...

Answer 7

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as possible go…

view full answer...

Answer 8

Our horse trailer pad items such as 60-inch Side Pad #HTP60BK and 24-inch Breast Pad #HTP24BK don't come with included hardware because the requirements between different trailers can vary so much depending on the type of material the pads are…

view full answer...

Answer 9

If you wanted to wire the 6" Oscillating Fan 12-Volt #PTW1658 to your trailers wiring you'd need to run it to the 12 volt accessory circuit as this circuit is designed for powering accessories like this or interior lights. I recommend the…

view full answer...

Answer 10

Horse trailer pad #HTP24BK does not come pre-drilled because then it would limit what and where it could fit. We also recommend trailer horse pad screw #PS-8 to mount the pad. The screws are sold in quantities of 1.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Do You Attach Horse Trailer Side Pads # HTP60BK To The Horse Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching