Recommended Locking Pin for Demco DM69FR Trailer Coupler

Question

Question:

Do you sell a locking pin for the Demco DM69FR

asked by: James R

0

Expert Reply:

We certainly do! The hole in the # DM69FR coupler that the locking pin would pass through is 5/16, which would easily accept the 1/4 inch diameter locking pin used by the etrailer # e98888 Coupler Lock.

I've linked to a product demonstration video featuring the # e98888 lock.

expert reply by: Mike L

0

Answer 1

Hey Robert, for your 2016 Jeep Wrangler using the Ready Brute Elite II tow bar you can use the Blue Ox Base Plate Kit #BX1126 with the Blue Ox Base Plate Adapter Brackets for Ready Brute Elite Tow Bars #BX88297. From here, to complete your flat…

view full answer...

Answer 2

Yes, your 2017 Chevrolet Equinox FWD can be flat towed with all 4 wheels on the ground. Do understand that you will need to run your Equinox for 5 minutes every time you stop for gas to properly lubricate your transmission and before towing. A better…

view full answer...

Answer 3

Hello Curtis. You can absolutely use an RV mount tow bar with your 2006 Ford E350 Van. For example, the Blue Ox Avail Non-Binding Tow Bar #BX7420 is compatible with any 2" hitch receiver. This could be on a motorhome, van or pickup truck. As…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, the Timbken bearings part #TMK73VR and #TMK23VR are made in the USA.

view full answer...

Answer 6

I called Cequent, the manufacturer, and have an answer for you regarding the Bulldog Cast Head Coupler with Wedge Latch - 2-5/16 inch Ball - Flat Plate Mount - 20,000 pounds, #BD4420000317. The bolt holes are 5/8 inches. This Coupler can also be…

view full answer...

Answer 7

You would be able to go to the larger tire size of 235/75R17.5 like the part #P35175 to replace what you have and you would have additional weight capacity which could help with the blow outs you are having. You did mention all of the usual suspects…

view full answer...

Answer 8

That is not normal wear for the L-Brackets on your Blue 2-Point #BLU75FR to be that worn. It looks like you have too much angle in the head, so I recommend trying to tilt the L-brackets a little to try and get the bar less on just that one edge, and…

view full answer...

Answer 9

I don't have the length of the spring bar arms on the Blue Ox 2-Point Weight Distribution System like part #BLU75FR but I can tell you that the frame brackets will need to be installed between 25-27" back on the frame from the center of the…

view full answer...

Answer 10

The only differences between the Demco Trailer Coupler #DM14976-52 and #DM88XR are the colors and the mounting bracket design. The part DM14976-52 is silver and has a straight, or no-drop, design with the bottom of the coupler being towards the top…

view full answer...

Answer 11

Yes, for 5,200 standard trailer axles we have the hub part #8-219-4UC3-EZ which is a fit for 5,200 lb axles and has the bolt pattern of 8 on 6-1/2 inches like you said you need.

view full answer...

Recommended Locking Pin for Demco DM69FR Trailer Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching