Are Holes in LaSalle Bristol Double Bowl RV Kitchen Sink Centered

Question

Question:

Are the sink holes centered and will it be compatible with a 2” hole?

asked by: Candy P

0

Expert Reply:

The holes in the LaSalle Bristol Double Bowl RV Kitchen Sink # 34413TGS331974 are centered. The 3 holes for the faucet are centered to the overall dimensions and have a 1-12" diameter while the drain holes are centered in the bowls and have a 3-1/2" diameter.

Attached is a review video that goes over these dimensions.

expert reply by: Jon G

0

Answer 1

The overall length of the Better Bath RV Kitchen Sink #LC388415 is 32" while the width is 17-5/8" for the larger sink and 15" for the smaller sink. The flange on the outside is about 1" wide which gives you an idea of the area you…

view full answer...

Answer 2

The best solution that we have for you is the LaSalle Bristol Utopia Sink #34413TGS331974 which measures 33" x 19" x 7" and is stainless steel. This is a bit bigger than what you are replacing so you need to make sure that you have…

view full answer...

Answer 3

I suppose you could drill a hole into the Better Bath RV Kitchen Sink part #LC388412 to mount your faucet/tap but that is not really it's intended use as it is mainly used in under-mount applications. If you were to use this sink as a top-mount…

view full answer...

Answer 4

The Replacement Return Spring Kit for Power Gear External Spring RV Leveling Jacks #LC359434 is the 500094 spring that you are looking for. The 500094 is an alternate part number for the Replacement Return Spring Kit for Power Gear External Spring RV…

view full answer...

Answer 5

I reached out to my contact at LaSalle-Bristol and they confirmed that this is a 20-gauge metal sink, slightly better than 22 gauge. Thanks for pointing that out.

view full answer...

Answer 6

We have a double bowl kitchen sink setup that measures 33 by 19 inches like you are looking for with the LaSalle Bristol part #34413TGS331974. I attached a review video for the sink for you to check out as well.

view full answer...

Answer 7

Actually the type of roof vent cover you need to attach to the vent cover brackets of your Maxxair 4951KS like part #MA00-04500K is the part #MA00-955003 which uses those brackets with the included cotter pins of the cover.

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Are Holes in LaSalle Bristol Double Bowl RV Kitchen Sink Centered

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching