Can the T-Handle Door Latch Assemblies # L4080 Be Ordered Keyed-Alike?

Question

Question:

If I buy 4 of these locks can i have them keyd alike

asked by: Allan

0

Expert Reply:

According to my Redline representative, all of the # L4080 T-Handle locks are keyed alike.

I have confirmed this myself by pulling a few of them off the shelf in the warehouse. They all use the same key number, so if you order four of them, they will all be keyed alike.

expert reply by: Mike L

0

Tex

4/4/2024

Not much for security, anyone who has same mechanism has access .

Reply

Mike L.

4/10/2024

@Tex True, but this isn't very widely known.

Reply

Answer 1

I went out to the warehouse and measured a T-Handle Locking Stainless Steel Flush Door Latch, #L4080. The overall depth is 2-3/4 inches. The latch on the back side is adjustable and will fit on a door that is a 1-3/8 inches thick to 1-11/16 inches…

view full answer...

Answer 2

I spoke to my contact at Redneck and he gave me the dimensions of this T-Handle Locking Stainless Steel Flush Door Latch #L4080. Check out the picture I attached to see all the dimensions. The only one that is not listed on the picture is the depth…

view full answer...

Answer 3

I can offer what we have, though not make something work, it really depends on what size your wheel is. There is a 3,500 lb Timbren Axle-less system that is designed for use with larger tires and fits a hub with a 6 on 5-1/2" bolt pattern,…

view full answer...

Answer 4

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 5

Check out the dimension picture I attached for the Latch Part #L4080 that you referenced. I believe the dimension you are looking for is 1/2 inch on all sides from the edge of the latch flange to the center of the mounting holes.

view full answer...

Answer 6

If the hole in your door for the handle measure 2-3/4" x 3-3/4" the #L4080 would work, but most likely you would need a handle like the part #L1883 as that is more like the latching style of your current handle. This latch installs…

view full answer...

Answer 7

The Redline T-Handle Door Latch, part #L4080 can be mounted in any position you choose. You will just need to make sure the latching bar will catch, wherever the door latch is mounted. The amount of throw on the latch is 1-1/2 inches. See the…

view full answer...

Answer 8

I went out to the warehouse and pulled a Replacement Locking T-Handle, #UWSTHLOCK, and took some measurements. The overall width is 4-3/4 inches. The overall height is 4-13/16 inches. The mounting holes are 3-7/8 inches apart on center from side to…

view full answer...

Answer 9

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a…

view full answer...

Answer 10

The plunger for your TriMark 060-0460 is not offered as a replacement, however I do have another solution. Your best course of action is to install a complete replacement lock, like the Global Link RV Baggage Door Slam Latch #295-000078. This RV…

view full answer...

Can the T-Handle Door Latch Assemblies # L4080 Be Ordered Keyed-Alike?

Product Page this Question was Asked From

Continue Researching