Remote Control for my MaxxFan Roof Vent w/ 12V Fan 4301K

Question

Question:

Is there a remote or wall switch that works a Maxxfan 4301K

asked by: Jim M

0

Expert Reply:

Yes the Replacement Remote for MaxxAir Roof Vent Exhaust part # MA00A01151K is designed to work with your MaxxFan Roof Vent w/ 12V Fan part # MA00A01151K

expert reply by: Randy B

0

Answer 1

The correct manual override cover for your 3,500lb electric Ram jack is the Replacement Manual Override Cap for etrailer A-Frame Electric Jack #EJ-3520-BCP. For a cover you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks…

view full answer...

Answer 2

The model number for fans such as the MaxxAir MaxxFan Mini Roof Vent, #MA00-04401M is listed on the upper side of the assembly itself. Please see the attached image. You will best identify this by opening the vent and climbing on top of the RV.…

view full answer...

Answer 3

The model number for your MaxxAir vent like the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan #MA00-04401M, can be found on a sticker stamped on the upper side, if you can't find it there you can also find it located on the bottom and visible…

view full answer...

Answer 4

To remove the screen for the MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White, #MA00-04000K, you simply remove it from the 4 mounting tabs. These tabs rotate. I've attached a picture for…

view full answer...

Answer 5

I spoke with my contact at MaxxAir who said that if you lost the remote to your MaxxAir fan there is no programming that has to be done when using a replacement remote. Part #MA00A01150K is already compatible with all MaxxAir fans that have…

view full answer...

Answer 6

The Maxxair website doesn't list the 4900K as coming with a remote control option. It may have been something added by a manufacturer. The Replacement Handheld Remote for Maxxair Roof Vent Intake/Exhaust Fans - Qty 1 #MA00A01150K or the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for…

view full answer...

Answer 12

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Remote Control for my MaxxFan Roof Vent w/ 12V Fan 4301K

Product Page this Question was Asked From

Continue Researching