Solution for Leaking Model 10 Trailer Actuator that Leaks

Question

Question:

Can I buy just the gasket or seal? I have the original cap model 10 but it doesn’t have anything to seal it and leaks

asked by: Mark

1

Helpful Expert Reply:

Just the gasket/seal is not available for the Replacement Master Cylinder Cap with Diaphragm for Titan Model 10 and 20 Brake Actuators # T4830601 that you referenced so your best option is to go with an all new cap to stop the leak you have.

expert reply by: Jameson C

1

Answer 1

For the Titan model 60 filler cap, a little penetrating oil may be wise around the seal and tap the cap to let the vibration move the fluid. If you have a 1-1/4 inch socket with a breaker bar, that is probably your best option. If not, some channel…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Solution for Leaking Model 10 Trailer Actuator that Leaks

Product Page this Question was Asked From

Continue Researching