Can Ark Ezi-Guides Self-Aligning Boat Trailer Loading System be Used at Front of Trailer

Question

Question:

can these be used as an alignment roller toward the front of a boat trailer rather than the rear. I have a 25 ft Albin with a full keel that runs the length of the boat. The trailer is a bunk trailer. There are two rollers toward the bow. The boat just needs a little guidance at the bow for the last 2 ft.

asked by: Robert B

0

Expert Reply:

Sure they can; there's no reason you can't install the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System # AR84FR to the front of your trailer if you like. So long as you have the 1.96" to 2.57" cross beam to mount the U-bolts you can install these at the front of your trailer.

I have added a link below to a video review for you to check out as well of the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System # AR84FR.

expert reply by: Kyle S

0

Answer 1

I do have a photo of the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System part #AR84FR installed which you can see below. This should give you a better idea of what is involved but it's not complicated at all. These work really well and…

view full answer...

Answer 2

I don't have a video I can share with you, so the attached photos are the best I can do to hopefully give you an better idea of how the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System - 20' to 28' Long Power Boat #AR84FR work.…

view full answer...

Answer 3

The keel roller will help to center your boat as the wobble rollers you have allow the boat to sit slightly to one side or the other. We do offer the CE Smith Keel Roller #CE29505 which has a self centering design to help guide your boat to the…

view full answer...

Answer 4

The installation process of the Ark Ezi-Guides Self-Aligning Boat Trailer Loading System -part #AR84FR is very easy and can be done by you easily. It will use u bolts to wrap around the trailer frame and you will then tighten them down with either a…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Can Ark Ezi-Guides Self-Aligning Boat Trailer Loading System be Used at Front of Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching