Will The Electronic Trailer Brake Kit Fit My Axle?

Question

Question:

What is the center to center distance between the mounting flange bolt pattern? Are they equal distance? Specs: Application: most standard hub-and-drum assemblies, including Dexter, Lippert LCI, and AL-KO Dimensions: 10inch diameter x 2-1/4inch wide Mounting flange bolt pattern: 4 bolt Wheel size: 14inch and 15 Axle rating: 3,500 lbs

asked by: Ed W

0

Expert Reply:

The mounting flange bolt pattern is a very standard pattern. It seems like the holes are an equal distance away from eachother. As long as you have a 3,500lb axle or less and any 14/15 inch wheel you should have no issue using our trailer brake kit # AKEBRK-35-SA. I've found that when the break kit gives the application as "most standard hub and drum assemblies" there isn't much fitment issues.

expert reply by: Adam E

0

Answer 1

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS #DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

The mounting holes for brake assembly #AKEBRK-35L are indeed 4 inches diagonally from the center of one to the center of the other. Side to side or top to bottom the holes are spaced approximately 2-7/8 inches apart on center. The pilot hole is…

view full answer...

Answer 4

I went out to the warehouse to take some measurements of brake assembly #AKUBRK-35R-D. The bolts are spaced 2-7/8 inches apart on center (side to side and up and down). The center hole is approximately 3 inches in diameter. The matching left side…

view full answer...

Answer 5

The center diameter of the rotor of the part #K2R35S is 3.6 inches. The bolt pattern for the 4 holes of the mounting flange are of the same standard pattern for trailer brake assemblies. The bolt holes will be 2-7/8 inches left to right and…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Will The Electronic Trailer Brake Kit Fit My Axle?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching