How to Remove Cupholder From Thomas Payne Momentum Recliner

Question

Question:

How do I remove the cupholder from the recliner to see if it is the problem

asked by: Sandra B

0

Expert Reply:

If you need to remove one of the cup holder assemblies on your Thomas Payne Momentum Recliner you can do so by first locating the notch on the side of the cup holder that you should be able to feel with your hand. Then it's just a matter of using something like a flathead screwdriver to pop up the cup holder using this notch.

Once the unit is popped up from its recessed opening there will be 2 screws revealed that need to be removed before you can completely detach the cup holder wiring from the sofa.

For the replacement cup holder itself you can use part # 195-387597.

expert reply by: Erik B

0

Answer 1

I spoke with my contact at Lippert who said that there is a notch in the side of the cup holder that you should be able to feel with your hand. Once you find it you will need to use a flathead screwdriver or a butter knife to pop it up. This will…

view full answer...

Answer 2

For your Thomas Payne dual reclining loveseat, there could be a number of reasons why your recliner will not recline any longer. Lippert, the manufacturer of these recliners, has recommended you first unplug the unit from power, and let it sit for…

view full answer...

Answer 3

Since your Thomas Payne Recliner has no power for any function, I recommend first plugging something into the outlet to make sure that isn't the issue. Next, I recommend checking the Cup Holder #195-387597 and it's wiring connection because…

view full answer...

Answer 4

I spoke with my contact at Lippert who said that either the heater is bad or the control box needs to be replaced on your Thomas Payne Momentum recliner. To test the heater unplug the red and black wires from the control box (located behind and under…

view full answer...

Answer 5

I spoke to my contact at Lippert and we were able to determine that you need the Replacement Theater Heating Seat Kit part #195-000113. I have attached a photo of this part for you as well. If this is not what you were referring to then please send…

view full answer...

Answer 6

The recliners run off of 110V AC, using a standard 110V outlet. So, if your camper doesn't already have a power inverter you could use one like the Go Power #34280176. If your loveseat is a Thomas Payne model, you can use the #195-387595…

view full answer...

Answer 7

It sounds like you've got a Thomas Payne Seismic Dual Power Reclining RV Loveseat w Console, Heat, Massage, LEDs like the #195-091-092-090, and you need the power plug for it. In this case you'll want to use the Replacement Power Cord with…

view full answer...

Answer 8

The Replacement Cup Holder for Thomas Payne Momentum Recliners #195-387597 will work for the Momentum series recliners (#'s 195-000055, 195-000056, 195-000055-056, 195-055-056-058, and 195-055-056-057) if you have one of those models then this…

view full answer...

Answer 9

Try removing the good working cupholder and installing it on the side that isn't working. Most likely that will fix the issue and indicates that you need a new cupholder like with the part #195-387597 that you referenced.

view full answer...

Answer 10

You could test the wiring of the heating pad with a circuit tester like the part #PTW2993 to see if there is voltage to it when the heating function is on. If you are getting voltage but the seat isn't heating you'd want to replace the heater…

view full answer...

Answer 11

We have the control box you are looking for with the part #LC36FR.

view full answer...

Answer 12

Thanks for the picture of your current module. Based on that the correct replacement module is the part #LC36FR that you referenced.

view full answer...

How to Remove Cupholder From Thomas Payne Momentum Recliner

Product Page this Question was Asked From

Continue Researching