Measurement Between Two Mounting Holes On Short Side Of Bracket

Question

Question:

What is the measurement between the two holes in inches? on the short side of L. 2 inch?

asked by: Julian

1

Helpful Expert Reply:

The measurement between the two hole on short side of Angled Up Mounting Brackets for Rhino-Rack Sunseeker Awning - RSP, RS 2500, and SG Roof Racks Item # RR32123 is going to be 2" center on center.

expert reply by: Shane H

1

click to enlarge

Answer 1

I measured the spacing between the holes on the top and bottom of the Batwing and Foxwing Awning Relocation Kit for Rhino-Rack Heavy-Duty Crossbars #RR31102 for you and as you can see by the accompanying diagram, the distance between the top…

view full answer...

Answer 2

We don't have anything custom fit for the crossbars of your offroad trailer but you most likely could use the Angled Up Mounting Brackets for Rhino-Rack Sunseeker Awning #RR32123 that you referenced if you were okay doing some fabrication.

view full answer...

Answer 3

I attached a picture that has the dimensions of the brackets of the Mounting Kit for Rhino-Rack Batwing Awning #RR25FJ that you referenced.

view full answer...

Answer 4

Here are the 2 different mounting options for installing the Batwing and Foxwing Awning Relocation Kit #RR31102. You can change the orientation of the brackets so that the awning will either hang higher or lower depending on your application.

view full answer...

Answer 5

The Rhino-Rack Foxwing Awning Mounting Kit #RR31105 is designed for use with smaller square bars like what Thule has. Since you have the Rhino-Rack Heavy-Duty Crossbars you need to use the Relocation Kit #RR31102 which was designed specifically for…

view full answer...

Answer 6

According to Rhino-Rack, the Angled Up Mounting Brackets #RR32123 will fit the #JA7973 but the Angled Down Mounting Brackets #RR32127 will not work. They are not compatible due to the design and the way the crossbars would mount on your 2021 Subaru…

view full answer...

Answer 7

If you are using the Rhino-Rack Vortex Aero Crossbars #RRVA180S you can use the ARB Awning with the Angled Up brackets #RR32123 but the hardware that connects the awning to the bracket are different. Notice on your awning it uses a bolt head to slide…

view full answer...

Answer 8

I have a great solution for you. Unfortunately, I confirmed with Thule that the AeroBlades TH7502B-TH7503B have not yet been tested on a Wilderness model of a 2022 Subaru Forester. For that reason, it is impossible to determine with certainty if they…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...