Replacement Master Cylinder for Titan Aero 7500 Brake Actuating Coupler for Disc Brakes

Question

Question:

Does the T4820000 replace the aero titan 7500 disc Also di I need to buy the push rod or can I use the old one ?

asked by: Vladimir A

0

Expert Reply:

The Replacement Master Cylinder Assembly for Titan Model 60 Brake Actuators - Disc # T4820000 is not the replacement you are seeking. Instead you will want the Replacement Master Cylinder for Titan Aero 7500 Brake Actuators - Disc # T4714200042 along with the Replacement Cover Gasket for Titan Aero 7500 Master Cylinders # DX37FR.

You can reuse the old push rod or you can use the Replacement Push Rod Assembly for Titan Model 60 Brake Actuator # T2346300 if desired.

expert reply by: Jason S

0

Answer 1

Since it sounds like the latch is the source of the problem you will want to replace it with a repair kit. The correct repair kit for your Titan Model 60 Multi-Fit coupler is the Latch Repair Kit for Titan Multi-Fit Couplers and Brake Actuators…

view full answer...

Answer 2

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the…

view full answer...

Answer 3

While there is not a rebuild kit for the Titan Model 60 brake actuator, we do have several replacement parts available. Replacement Master Cylinder Assembly for Drum Brakes - part #T439510 Replacement Push Rod Assembly for Brake Actuator - part…

view full answer...

Answer 4

At its widest point the Demco Hydraulic Brake Actuator - Drum - Primed - A-Frame - 2-5/16" Bulldog Coupler - 8,000 lbs #DM8759802 measures 17 inches, and the total length is 30 inches.

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...