Replacement Dust Cover for Bearing Buddy that Measures 2-1/2 inches Across

Question

Question:

I cant find the model number for the bearing buddy on my trailer wheels. The dimension of the one dust cover I do have is 2 1/2 across the top. What model would I need to replace this size bearing buddy bra?

asked by: Debora

0

Expert Reply:

The Bearing Buddy Replacement Bras you will need are part # BB23B, model 23B.

expert reply by: Robert G

0

Answer 1

The Bearing Buddy Replacement Covers, #BB19B, are made to fit the Bearing Buddy bearing protectors. If the bearing protectors that you have say 1.980, then that would be the size you would need. The only dust covers I sell separate are for the…

view full answer...

Answer 2

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 3

When selecting bearing protectors the measurement needs to be as accurate as possible so you will need to use dial calipers. We have a digital set we use here for precise measurements. Since 2.24 is too large and 1.98 is too small the size in the…

view full answer...

Answer 4

According to my research it looks like the replacement EZ Lube grease cap size you're needing is for a 1.98" hub bore which means you can use part #DC200L-DCRP for 1 grease cap or part #RG04-040 if you need to order 2 caps. Then for…

view full answer...

Answer 5

The Bearing Buddy Replacement Bras you will need are part #BB23B, model 23B. This cover is designed to fit Bearing Buddies with an outer diameter of 2-1/2 inches.

view full answer...

Answer 6

Yes. The Replacement Bearing Buddy Bras for your Bearing Buddies are #BB19B. These covers have a little bit of adjustability as the Bearing Buddy can change shape slightly when being installed.

view full answer...

Answer 7

I have a couple close but not perfect to your measurements. The 2" Lubed Dust Cap & Rubber Plug - 1.99" part #DC200L-DCRP is an extremely common cap size found on a lot of trailers. Sometimes the hub will have a small bevel on them that…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Replacement Dust Cover for Bearing Buddy that Measures 2-1/2 inches Across

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching