Is the Drawbar Pin and Clip Included With Draw-Tite, 36423, Class II Receiver Hitch on 2009 Jeep
Question:
wanted to know if drawbar and pin are included
asked by: sith k
Expert Reply:
No, the draw bar, pin and clip are not included with the Draw-Tite Class II Trailer Hitch, part # 36423. The manufacturer recommended drawbar for the 2009 Jeep Patriot is, part # 36061, which needs to be used in the rise position only. You will also need a hitch pin and clip, part # PC2, and a properly sized hitch ball, part # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter).
If you do not already have trailer wiring, you will need the T-One Vehicle Wiring Harness, part # 118552, to set your vehicle up to power your trailer lights. I have included links to the installation instructions for the hitch and wiring, and a link to a video showign a typical installation of the hitch.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Curt or Draw-Tite Trailer Hitch For 2020 Honda Fit
- Q&A: Comparing Draw-Tite DT24959 and Curt C11286 Class I Hitches for 2014 Subaru Impreza Wagon
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What Is The Difference In A Grease Seal Labeled 171255TB and A Seal Labeled 171255VB
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Light To Replace Older Reflecto Light 110-150 On Travel Trailer
- Q&A: How Does Replacement Operator Mechanism for MaxxAir MaxxFan Plus MA10-20281K-1AF Install
- Q&A: Recommended Trailer Hitch and Installation Information for 2012 Jeep Compass
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Article: 5 Things to Know About Weight Distribution Hitches