What is the Maximum Tire Width that Will Work With the Hollywood Racks Parking Stand

Question

Question:

I have an mountain ebike with WTB Ranger 2.8 27.5inch tires the 2.8s are technically 2.75 inches wide, will they fit in this rack? I ask because your 8/16/20 reviewer Jim of the 3 bike stand Swagman Bike Storage - S64018 commented that he had no problem with his 3inch wide tires for the 3 bike stand, even though I believe thats also specd for 2.5inch wide max. I would prefer to buy 3 separate HRPS1 stands rather than the 3-unit product. Thank you.

asked by: Richard

0

Expert Reply:

The Hollywood Racks Bicycle Parking Stand part # HRPS1 is designed for a max tire width of 2.5". There is only 1/4" of difference between your tire and the racks maximum. This means the racks could be "modified" slightly to accept it but of course you would be bending the rack.

For an option that will work without "modifications" the Saris The Boss Bike Storage Stand part # SA6014 is a great stand that uses the back wheel to secure the bikes and works with most all tire sizes.

expert reply by: Randy B

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

What is the Maximum Tire Width that Will Work With the Hollywood Racks Parking Stand

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching