Can Screws Only be Purchased for the Replacement Mounting Hardware for Lippert Solera Slide Topper

Question

Question:

Can you purchase only the #10 16 x 3/4” screws? I only need the screws for the hardware.

asked by: Chris

0

Expert Reply:

The screws that are part of the hardware cannot be purchased separately from the Replacement Mounting Hardware for Lippert Solera Slide Topper # LC701665.

Those screws are only with this kit.

expert reply by: Kyle S

0

Answer 1

I have linked the installation instructions for one of our Solera Slide-Out Awnings #LCV000165062 below. While the mount for these have changed from the Replacement Mounting Hardware #LC701665 you will still be able to see how everything is…

view full answer...

Answer 2

The Replacement Mounting Hardware part #LC701665 comes with the Extension Rods, Extension Rod Bracket, Torsion Arm Caps, and various hardware. I am not sure what all you have now but it sounds like you might also need the torsion heads, part #LC87FR…

view full answer...

Answer 3

The Replacement Drive Head and Roll Tube #LC34FR is the correct assembly for the right hand side of your Solera Slide topper as you stand facing it from outside the camper. The Replacement Idler Head and Roll Tube #LC87FR is on the left hand side as…

view full answer...

Answer 4

For replacing the Drive Head #LC34FR and Idler Head #LC87FR on a Solera Slide Topper you will want to completely remove the slide topper from your RV/Camper. You will need to insert a pin into the end of the tube end cap(see image) to keep the…

view full answer...

Answer 5

The Lippert Solera Slide-Topper Awning #LCV000163289 does not have an anti-billowing device. My technical contact at Lippert/Solera advised that their awnings have enough spring tension to prevent unintended extension of the awning fabric, even when…

view full answer...

Answer 6

Replacement Mounting Hardware for Lippert Solera Slide Topper - Black #LC701665 uses #10 - 16 x 3/4” screws to secure the shaft of the extension rod bracket. I've attached a photo to assist.

view full answer...

Answer 7

I have a solution for you, but my contact over at Lippert tells me that you won't be able to replace just those casings on Solera Slide-Out Topper. The parts you need are the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning -…

view full answer...

Answer 8

The amount of times you'd need to wind a Solera awning when installing it is 14 times. The part number you have 285148 matches up with the #LC87FR.

view full answer...

Answer 9

I contacted the manufacturer about the proper installation of the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning #LC87FR. It should be installed approximately 5-6 inches away from the side of the camper (slide topper opened…

view full answer...

Answer 10

You do not have to remove the entire slide topper to be able to replace the Idler Head and Roll Tube #LC87FR for your Solera slide topper. A second person will be able to support the weight of the tube and fabric in place while the assembly is…

view full answer...

Answer 11

For your application you either need the Drive Head #LC34FR or the Idler Head #LC87FR. These come with the roll tube as well. I'm not sure which one you broke but the idler head will be on the left side while the drive head is on the right if…

view full answer...

Answer 12

I see that you are asking about the Replacement Mounting Hardware for Lippert Solera Slide Topper kit #LC701665. You can purchase the Replacement Slide-Out Hex Bar Extension Bracket #LC2724412 and Replacement Awning Extension Rod #LC3452072 that come…

view full answer...