How Much Does the Kodiak Trailer Hub for 3500-lbs Axles Weigh

Question

Question:

What is the weight of this hub?

asked by: Julius F

1

Helpful Expert Reply:

The Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel # KH84545S weighs roughly 8-lbs.

expert reply by: Erik B

1

Answer 1

It is very likely that you have a 2100 or 2200 lb axle on the trailer however, the only way to know for sure is to find a tag on the axle itself. If you are not able to find the sticker on the axle we can narrow down the search with other…

view full answer...

Answer 2

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 3

Yes, we do offer idlers hubs with a 5 on 4-1/2" pattern compatible with Kodiak Slip-On Disc Brake Rotors, the Kodiak Trailer Hub for 3,500-lb Axles part #Q-HUB84545 for galvanized or part #KH84545S for stainless steel. Please note, these do not…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

How Much Does the Kodiak Trailer Hub for 3500-lbs Axles Weigh

Product Page this Question was Asked From

Continue Researching