How To Confirm Fit of the Landing Gear Set RVLG-8000

Question

Question:

I have a 2004 Nu Wa Snowbird LS. Cap on landing gear has these numbers-VMC900L-048265 will the RVLG-8000 replace these? Thanks,

asked by: James E

0

Expert Reply:

I won't be able to confirm the correct landing gear set for a trailer based on the make/model nor by cross referencing any part numbers but most are fairly standard and it's super easy to confirm this yourself. The Landing Gear Set part # RVLG-8000 is a very popular option that fits most trailers. In order to confirm it fits your particular application you''ll need to measure the distance between the weld stops on the existing legs and ensure they are 15-1/2".

expert reply by: Conner L

0

Answer 1

Normally when people say they have a 11-1/2 inches they are measuring between the brackets like you mentioned but the measurement to look for is on the outsides which for you would be 15-1/2 inches and the etrailer Landing Gear Set, part #RVLG-8000…

view full answer...

Answer 2

I have attached a photo for you that shows how to properly measure the outer tube on a landing gear leg. I have not heard of a landing gear leg with a 36-1/2" long outer tube so if this is what you have then I recommend you replace both the lead…

view full answer...

Answer 3

Most likely yes since the Landing Gear Set part #RVLG-8000 is a very universal kit designed to fit the majority of fifth wheel trailers out there but you'll have to measure the mounting brackets that are on your trailer currently and compare them…

view full answer...

Answer 4

It is possible that there is a part number somewhere that would help identify the landing gear on your trailer. Sometimes there is information on the underside of the caps on the tops of the jacks so that is another place you can check if you…

view full answer...

Answer 5

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

Answer 6

Though there is not a technical drawing of Landing Gear Set #RVLG-8000 available, there are plenty of dimensions I can give you. The non-technical (but still useful, hopefully) diagram below shows the distance between weld stops, which is 15-1/2…

view full answer...

Answer 7

The installation of the Landing Gear Set part #RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part #LC113511 to it, 15-1/2" apart. Once these are installed you…

view full answer...

Answer 8

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

How To Confirm Fit of the Landing Gear Set RVLG-8000

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching