Are Stainless Brake Pads Available for Kodiak Disc Brake Kit # K2R35S

Question

Question:

Concerning the brake pads for this kit I need to know if the brake pads included have Stainless steel backing plates? There seems to be conflicting info on this in the question section.... there are 2 questions on this and 1 answer is yes the other is no..... can you definitively answer if they are or not?

asked by: Daren M

0

Expert Reply:

The brake pads that come with the # K2R35S are the # K225CP which are made of carbon ceramic and have a lifetime warranty. If you did want stainless calipers as well you'd want the part # K225CPSS to.

expert reply by: Jameson C

0

Answer 1

I contacted the manufacturer to confirm that the Replacement Mounting Bracket for Kodiak Disc Brake Caliper #KCMB10RS will work with your Kodiak Disc Brake Caliper #KDBC225S (225 SS). They were able to confirm that those two parts will work…

view full answer...

Answer 2

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket #KCMB10RD.

view full answer...

Answer 3

The Kodiak Disc Brake Kit - 10&quot; Rotor - 5 on 4-1/2 - Stainless Steel - 3,500 lbs #K2R35S you were looking includes brake pads with the standard steel backing plate. If you would rather have brake pads with a stainless steel backing…

view full answer...

Answer 4

There would be a slight advantage to using 7,000 lb brakes in place of 6,000 lb brakes. The 7,000 lb brakes would not have tow work quite as hard reducing heat build up, but for the weight of your trailer, the 6,000 lb brakes should be able to…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…

view full answer...