Does Blue Ox SwayPro Weight Distribution System Allow Backing Up?

Question

Question:

I have to reverse at a tight angle to make it into my driveway and there is a rise to the driveway, making it necessary to keep my weight distribution bars on so I dont bottom out. Will this system allow me to do this without unhooking the bars before backing up?

asked by: Terry N

1

Helpful Expert Reply:

Yes. The Blue Ox SwayPro Weight Distribution w/ Sway Control - Clamp On - 10,000 lbs GTW, 1,000 lbs TW # BXW1000 does allow backing up with the spring bars engaged. The turning angle and incline of the driveway won't be an issue as long as the bars have ground clearance for function.

expert reply by: Jason S

1

Answer 1

With weight distribution systems you can't really make tight turns while backing up. What we recommend is that if you are basically backing up in a straight line you can leave the spring bars on the system. But if you think you will end up…

view full answer...

Answer 2

There are several holes on the frame brackets of the Fastway e2 Weight Distribution #FA94-00-1061 that can be used for attaching them to the trailer frame which allows them to fit trailer frames that are up to 6 inches in height.

view full answer...

Answer 3

The best way to make sure you have the proper tension on a friction sway control bar is to just do some testing of your own. The reason for this is because the amount of tension needed will vary from trailer to trailer. The owner's manual for the…

view full answer...

Answer 4

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 5

If you don't have enough tongue weight relative to the total trailer weight you'll end up with bad sway problems like you mentioned. The tongue weight of the trailer needs to be 10 to 15 percent of the total weight of the trailer otherwise…

view full answer...

Answer 6

The Blue Ox #BXW1000 SwayPro is designed for trailers with tongue weights ranging from 750-1000 lbs. If the fully loaded and ready to pull trailer tongue weight of your travel trailer is less than 750 lbs, you'll have a pretty rough ride and the…

view full answer...

Answer 7

The Solera Screen Room for 20' RV Awning part #LC362223 does have a door although it's not visible from the stock photos. The door is located in the corner of the screen room and rolls up and down when needed. I have attached a photo of the…

view full answer...

Answer 8

I would be happy to help! The Solera Screen Room #LC362223 you were looking at actually does not get attached to the awning arms. It has mounting brackets that get installed underneath the main awning rail on the side of your camper, and then gets…

view full answer...

Answer 9

We can tell you how to determine the correct screen room, but don't have any way of knowing what will fit any specific RV. It's not that difficult to figure out though, requiring just a simple measurement. All you need to do is measure your…

view full answer...

Answer 10

Yes, having the 1,000-1,500LB Spring Bars #BXW4008 will be good to use if your tongue weight does exceed the 1,000lbs the Blue Ox SwayPro Weight Distribution #BXW1000 you currently have are rated for. You will likely want to carry a etrailer Tongue…

view full answer...

Answer 11

Springs bars from Blue Ox that have two dots (sometimes called dimples or notches) are rated for up to 750 lbs of tongue weight. What you have are the Spring Bars for Blue Ox SwayPro Weight Distribution System #BXW4006.

view full answer...

Answer 12

We have the perfect solution but the Furrion Vision S W is not compatible with the pre wiring from Voyager. Instead the Voyager WiSight Wireless RV Backup Camera #ASA24YR is the way to go. This will allow you to use the already existing bracket to…

view full answer...