Direction of Tapered Nut When Installing Replacement Hardware Kit for Fulton Swivel Jack

Question

Question:

Can you advise on the direction the tapered nut should be installed? Does the tapered end thread first and go on towards the trailer and seat on the bushing? Is there a reason it does not thread easily, is it designed to lock in place or something? Also, there still is some play in the jack stand where it bolts to the trailer. The play is left ot right or out to in versus fwd and back as it is locked with the spring pin. Is this normal?

asked by: Donald

0

Expert Reply:

The tapered end of the nut that comes with the Replacement Hardware Kit for Fulton Swivel Jack
Item # F0933325S00 does go first. The nut is hard to thread on as it is a lock nut designed not to loosen up over time.

expert reply by: Jameson C

0

Answer 1

If the swivel jack you have is a Fulton the sleeve washer that comes with the part #F0933325S00 that you referenced would replace what you have and would prevent your jack from leaning like you mentioned.

view full answer...

Answer 2

The Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 is held on to the trailer with a center bolt. It is also the pivot bolt. Use a box end wrench or a short wall socket to remove the existing bolt. It has pretty coarse threads and generally they…

view full answer...

Answer 3

Since the manufacturer advised that the correct replacement part is Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00 I strongly recommend you use that specific part as there are no comparables and sometimes parts may be correct but not…

view full answer...

Answer 4

The small, round bushing that is included with the Replacement Hardware Kit, #F0933325S00, is not available by itself. The overall diameter of the bottom part is 1-1/8 inches. The diameter of the top part is 3/4 inches. The overall height is 7/16…

view full answer...

Answer 5

I believe what you're needing is the washer looking piece in the Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00.

view full answer...

Answer 6

The Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00 is a direct replacement from Fulton that is designed to fit only Fulton-model swivel jacks. However, there is a possibility that you will be able to use the hardware for your specific…

view full answer...

Answer 7

The shackle straps need to be placed on the outside of the rear leaf spring hangers which you can see in the attached photo. Furthermore, the distance between the two mounting plates (inside to inside) on your leaf spring hangers should be…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

Thank you for the photo it was helpful in determining what you need. The replacement would be the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which has a bolt-through mount, 1,200 lb lift capacity and has bracket heights of 12-3/4" retracted…

view full answer...

Answer 10

I went out to our warehouse and measured the 4 holes in the center of the Replacement Bolt-On Mounting Bracket for Fulton XP Series Jacks #F500349, and they measure 3" on center left and right, and 3" on center up and down. The remainder of…

view full answer...

Answer 11

You will be able to use the Bolt-On Mounting Kit #F500349 with the Mounting Hardware #F500286 to bolt on the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301.

view full answer...

Answer 12

It sounds like you are actually needing the Replacement Hardware Kit for Fulton Swivel Jacks #F0933325S00.This fits a mounting plate like the #P9012-00 that it sounds like you have welded to your trailer. It includes the metal bushing/washer that you…

view full answer...

Direction of Tapered Nut When Installing Replacement Hardware Kit for Fulton Swivel Jack

Product Page this Question was Asked From

Continue Researching