Troubleshooting Tailgate Latch Not Releasing With Lock LH-003 Installed

Question

Question:

As far as I can see in side the the tailgate, I have the lock installed correctly. Once on, the gate will not release. What can I do to correct it?

asked by: James W

0

Expert Reply:

The Integrated OEM Tailgate Lock - 1999-2007 GM Full Size Pickups # LH-003 prevent the latch from pulling in when the handle is pulled. The photos you show already have the sides pulled in pretty far so they are not able to move to release the outside latches. You may need to shorten the rods or increase spring tension on the rods to get the tailgate to work properly with this lock. Based on your photos there is no room for the rods to move to release the latches when you pull on the handle.

expert reply by: Jason S

0

click to enlarge

Answer 1

Sine you have a short-bed truck, in your 2006 GMC Sierra 1500 Crew Cab you can use one of the lock kits shown on the linked page. These fit all versions except the Crew Cab with 8-foot bed. For a manual lock you can use Pop & Lock kit #PAL1100…

view full answer...

Answer 2

When the Integrated OEM Tailgate Lock #LH-003 is properly installed on your 2005 Chevy Silverado the locking arms will sit above the rods but below the brackets that are connected to the arms. Basically those locking arms prevent the brackets…

view full answer...

Answer 3

I do have a lock that will fit your 2005 K3500 Silverado but it is not able to match the key to your vehicle keys. This Tailgate Lock #LH-003 has a nice OEM look and is a fairly simple installation. I've included a video to help you with the…

view full answer...

Answer 4

Pilot and Bully are one in the same so #LH-003 will fit your 2006 Chevy Silverado 1500. The bezel by itself is not available as a separate part.

view full answer...

Answer 5

I checked with Pilot and they do not exclude the 2005 GMC Sierra with standard bed so you can use #LH-003 on your truck.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I really like the Curt Trailer Hitch Receiver #C14108 for your 2005 Chevy Silverado 2500HD Short Bed because it has a hidden crosstube and is a Class IV rating so it's nice and sturdy for up to 10K trailers or 12K trailers if a weight…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 12

There is a difference between a 7-way round and and 7-way rv blade connector. If you take a look at the accompanying photo, which is from our linked article on trailer wiring you can see that the connector on the left has blade-style pins while the…

view full answer...

Troubleshooting Tailgate Latch Not Releasing With Lock LH-003 Installed

Featured Help Information

Miscellaneous Media

Continue Researching