Correct Trailair Flex Air 5th Wheel Pin Box for a 2020 Beacon Vanleigh 39GBB

Question

Question:

I would like to replace my current Pin Box - S/N: S003741620 - LCI Item #: 670452. I am looking at the FlexAir Pin Boxes and need to know which one to order? My 5th wheel is a 2020 Beacon Vanleigh 39GBB 18K

asked by: Dusty T

0

Expert Reply:

The correct Trailair Flex Air 5th Wheel Pin Box for a 2020 Beacon Vanleigh 39GBB is part # LC328492.

expert reply by: Conner L

0

Answer 1

The fitment of pin boxes like the Curt Flex Air 5th Wheel Pin Box #LC65VR are solely based on the bolt pattern for the trailer and not the tow vehicle. This specific pin box is a replacement for Lippert's Rhino Box bolt pattern. To determine…

view full answer...

Answer 2

You ordered the correct urethane dampener for your Demco Hijacker AutoSlide part #DM8550024. The 15769 and the 15469 basically represent the same part number now so the #DM15469 that you ordered will fit and work well!

view full answer...

Answer 3

I confirmed with Gen-Y that the measurement from the center of the kingpin to the rear bolt-hole setup is 24 inches on the Gen-Y Shock Absorbing 5th-Wheel Pin Box #GY46FR. I went ahead and attached a diagram that shows this measurement.

view full answer...

Answer 4

Thanks for the feedback on your Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box - Lippert 1621 #GY46FR! What you experienced is normal and there is a little bit of break-in time for these to really settle in and make a big difference.

view full answer...

Answer 5

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 10

Because it's lighter, less expensive, has fewer moving parts and is mechanically less complicated I'd recommend going with the Gen-Y #325-GH-8040 shock absorbing pin box versus a Trailair Flex Air like part #LC328492. The Trailair features a…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Correct Trailair Flex Air 5th Wheel Pin Box for a 2020 Beacon Vanleigh 39GBB

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching