Replacement Winch Cable for Jet Ski Winch that Weighs 1,100 lbs

Question

Question:

I was looking at the the Fulton galvanized winch cable with hook 25 x 3/16 - 4200LBS, to replace the cable mt jet ski davit. The ski weights 1100 LBS. and the cable loopks to be the same size

asked by: Vincent S

1

Helpful Expert Reply:

The Fulton Galvanized Winch Cable # FWC3250100 that you referenced would work great. It has more that enough capacity and it matches the dimensions you need as well.

expert reply by: Jameson C

1

Answer 1

From what I found your 1991 Chaparral 1900 Bowrider weighs 2,200 lbs so it is likely the 3,250 lbs is the GVWR of the trailer. The best option for a winch that will have plenty of capacity is the following: - 2-Speed Boat Trailer Winch #315-W2500D…

view full answer...

Answer 2

The Fulton T2005 2-speed winch has been discontinued, and as such there is not a replacement drum for it. While I know it's not the answer you were looking to hear, the only option we have for you is to replace your winch, and the direct…

view full answer...

Answer 3

We have the correct cable, but it does come separately from the Fulton High-Performance 2-Speed Trailer Winch #F142400. The correct part you will need is the Fulton Galvanized Winch Cable with Hook #FWC3250100.

view full answer...

Answer 4

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement Winch Cable for Jet Ski Winch that Weighs 1,100 lbs

Product Page this Question was Asked From

Continue Researching