Conspicuity Reflector Installation Options With or Without Mounting Screws

Question

Question:

Is there anything to plug the mounting holes so it is not noticeable if not used. If the mounting holes are used is there any kind of screw that would blend with the clear reflector?

asked by: John B

0

Expert Reply:

The Custer Clear Conspicuity Reflector, 12" Long # RFL-12W does not have any screw hole covers. The only way to get away from the screws is to use the White Conspicuity Tape, 150' Roll # 29804 which is 2 inches wide and can be cut to length.

expert reply by: Jason S

0

Answer 1

We have the 18 inch version of the Optronics reflector tape part #RE18T similar to the #RTR15066PB you referenced.

view full answer...

Answer 2

If you check out the help article I attached below you'll see info on when conspicuity tape is needed like part #RTR15066PB for 6 inch by 6 inch or part #RE18T for 7 inch by 11 inch. The size differences basically come down to what best fits…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Conspicuity Reflector Installation Options With or Without Mounting Screws

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching