Difference Between Valterra T1023 and T1026-1 RV Sewer Adapter Fittings

Question

Question:

What is the difference between the T1023 and T1026.1?

asked by: Ronald B

0

Expert Reply:

The # T1023 and # T1026-1 both have bayonet fittings on one end and lug fittings on the other. The only difference is that the # T1023 is a 90° fitting and the # T1026-1 is a 45°.

expert reply by: Mike L

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The AllTrek 4000 kits provide the best cushioning so if you were to upgrade from your CRE3000 kit to the Alltrek you would see a big improvement. If you have a 35 inch wheelbase you'd want the part #MR29DR or if you have a 33 inch wheelbase…

view full answer...

Answer 6

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear to…

view full answer...

Difference Between Valterra T1023 and T1026-1 RV Sewer Adapter Fittings

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching