Customers compare MCL165RB to these similar products
Products Featured in this Video
Today we're going to be taking a look at part number MCL165RB. This is the Optronics Glow Light Thinline series red LED clearance or side marker light. It's going to be sonically sealed so it has a water proof housing that is submersible. The Thinline series is going to feature a low profile design so that way the light can fit into tighter spaces. It is going to contain an LED system. LED's are… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…
view full answer...The closest LED tail light we carry to Bargman #30-92-002 that you referenced is part #328-003-81M1 for the passenger's side and #328-003-81LM1 for the driver's side. They're fairly close in size but don't have the…
view full answer...I have a few options for you to replace the Bargman 30-91-010 Tail Lights. There isn't a direct LED replacement. The Bargman Trailer Tail Light part #30-92-001 and part #30-92-003 are direct replacements but they are incandescent. You could…
view full answer...There are five mounting brackets available that fit the Optronics Trailer Clearance Side Marker Light #MC65AB. These three are all black plastic. They are Optronics #A65PBPG, #A65PB and #A65B. The first two come with a single wire, the…
view full answer...There are things that can be done to raise your gooseneck trailer suspension to help provide the proper ride height for your truck. First the capacity of the axles on your trailer should be determined, to be sure that the parts ordered will work…
view full answer...I would run a set of e-tracks down the length of the floor of your trailer like part #E19148 (5 foot section), and then use the wheel nets like part #EM58523 to secure the wheels of your cars to the tracks. Check out the install videos I attached as…
view full answer...Yes, you just have to remove the old lights, match the wires and mount the new ones. Please note, that it is usually not a good idea to mix LEDs and incandescent lights, so if you have have side markers or other lights on the trailer, make sure you…
view full answer...We don't offer a flat surface mount lamp that would include the license plate lamp, but the Diamond Group #DG52721PB would provide stop/turn/taillight and the reverse lamp. For a license plate lamp, you can mount something like #OPT77FR above the…
view full answer...The breakaway battery would usually be maintained from the 12-volt circuit coming off the 7-way trailer connector. You can test the battery with a volt meter to see if it's still good. It's unlikely that the breakaway battery would deplete…
view full answer...To power an electric trailer jack (or a winch for that matter) generally the higher the amperage rating of the battery the better. Jacks, like winches, use more power to operate as the load increases. The Ultra-Fab Electric A-Frame Jack #UF38-944017…
view full answer...Thank you for the picture. It looks like you have the Black Aluminum Bearcat Trailer Wheel. Although the black has been discontinued, we do still have the gunmetal gray #274-000039. This matches your current size and bolt pattern as well. To…
view full answer...You do want to charge the battery of the breakaway kit so that in the event you need it the brakes would activate like they need to. That being said that shouldn't affect trailer brakes performance as long as it was install properly. Your best…
view full answer...