Will Rhino-Rack Road Warrior Bike Rack Fit Channels of Yakima RailBar on 2019 Subaru Impreza

Question

Question:

I just purchased the Yakima RailBar Crossbars Y00448-0449 from E-Trailer. Ill be using this on my 2019 Subaru Impreza. I am looking at the Rhino-Rack Road Warrior Rooftop Bike Rack. Will the front T-mount on the Rhino rack work in the Yakima Crossbar?

asked by: Mike T

0

Expert Reply:

Yes, the front T-Bolts that come with the Rhino-Rack Road Warrior Rooftop Bike Carrier # RBC036 will fit in the channels of the Yakima RailBar Crossbars # Y00448-0449 that you'll be installing on your 2019 Subaru Impreza.

expert reply by: Jon G

0

Answer 1

The Rhino Rack Road Warrior part #RBC036 is a really great choice that fits the factory crossbars of your 2018 Honda Odyssey, is priced great, and comes with locks for the bikes and the rack. You might have to stagger the direction of the bikes as…

view full answer...

Answer 2

I spoke with my contact at Rhino Rack and the replacement part number you need is part #RBCA022 which is the replacement skewer for the Rhino Rack Road Warrior #RRRBC036.

view full answer...

Answer 3

The Rhino-Rack Masterkey Lock Barrels - Keyed Alike - Qty 2 item #RRRK093-2 will work on your 2500 series Rhino Rack with locking cylinder #093.

view full answer...

Answer 4

The hitches available for your Prius are Class I, which have a low tongue weight capacity (maximum amount of weight that can safely be suspended from the hitch) of 200 lbs. Because of this, the bike rack and the hitch manufacturers both agree that…

view full answer...

Answer 5

I spoke with Rhino Rack about the Rhino-Rack Road Warrior Rooftop Bike Carrier part #RBC036 and they stated there is a tab on the backside of the skewer that will need to be depressed with the key inside the lock and it being in the unlocked…

view full answer...

Answer 6

Try spraying WD40 into the lock core using the straw to direct it into it. That should free up any stuck tumblers.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Will Rhino-Rack Road Warrior Bike Rack Fit Channels of Yakima RailBar on 2019 Subaru Impreza

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching