Pop Up Camper Winch Upgrade Reinforcement

Question

Question:

Pop-up camper replaced the winch with a electrical winch. Original winch come out of the bumper. What do I need to do to support the winch so it stops bending the bumper/ support beams

asked by: Trisha B

0

Expert Reply:

If the Superwinch LT2000 ATV Winch part # 1120210 that you have attached to your pop up camper is bending the original brackets that your pop up was equipped with I recommend taking it to a local welding shop and having new and additional bracing welded in place. This will eliminate the issue you are running into with your current set up.

expert reply by: Randy B

0

Answer 1

We have 12 volt winches like the Superwinch LT2000 part #1120210 that would work well for what you need as this has a 2,000 lb capacity but we do not carry the specific winch you are looking for.

view full answer...

Answer 2

It is likely we have a motor to replace what has died. Can you offer any more information like a part number, manufacturer of the motor, etc? If you want to replace the entire winch system, then the Superwinch LT2000 ATV Winch - Wire Rope - Roller…

view full answer...

Answer 3

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We have the…

view full answer...

Answer 4

Either of these two options would work. You will need an electric winch that loads in an out, so you can raise and lower your pop up. The Superwinch LT2000 ATV Winch - Wire Rope - Roller Fairlead - 2,000 lbs, part #1120210, you attached to your…

view full answer...

Answer 5

The mounting bolt pattern for the Superwinch LT2000 Electric Utility Winch, #1120210, is two holes, 3.15 inches apart. This winch can be mounted in place of a manual winch and my contact at Superwinch assured me that the unit is waterproof so you…

view full answer...

Answer 6

The Superwinch LT2000 ATV Winch #1120210 does come with a switch that allows you to power the line in or out. It looks more like a rocker switch and will be permanently installed (see attached photo). If you were thinking of something more like a…

view full answer...

Answer 7

Using an electric winch such as #1120210 could work for your large 600 pound trailer door. You will need to use pulley blocks though because you need at least a 12 inch straight line pull in front of the winch. For a regular pulley block you can use…

view full answer...

Answer 8

The dynamic brake on the Superwinch LT2000 winch #1120210 is not meant to hold a load indefinitely so it would not really be the best option for you. I recommend a winch that has mechanical braking. Or you could use a worm gear winch which has a…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Pop Up Camper Winch Upgrade Reinforcement

Product Page this Question was Asked From

Continue Researching