Does the 7' Kodiak Hydraulic Brake Hose bh-3mfs-7 Come with 45 or 90 Degree Fittings

Question

Question:

I’m looking for seem Line with one said 45 Degree Or 90 degree thank you

asked by: Afteem

0

Expert Reply:

The Kodiak Hydraulic Brake Hose part # bh-3mfs-7 does not come with 45 or 90 degree fittings but you could add these with the Kodiak Hydraulic Brake Hose part # bh-3mfs90-1-5 and Kodiak Union Fitting part # BH-C-3FIF. In which case you might want to step down to the Kodiak Hydraulic Brake Hose part # BH-3MFS-3-5.

expert reply by: Conner L

0

Answer 1

The majority of our brake line fittings are made from brass which are a bit different than the steel brake line fittings you might be familiar with on a passenger vehicle. Generally speaking, the cause of these brass brake line fittings leaking is…

view full answer...

Answer 2

Sounds like you are trying to install the wrong brake line to the Kodiak Disc Brake Caliper #KDBC225S that you mentioned. The fitting size needs to be 3/16 inch like what comes with the #18TA-BLKIT. Since I don't know what brake lines you…

view full answer...

Answer 3

Normally trailer brake lines are only used on trailers. However, if your vehicle has brake line fittings that match what the part #18TA-BLKIT has and the psi of the system does not exceed 1,600 psi this line could work for you as these are SAE…

view full answer...

Answer 4

The Tekonsha Prodigy P3 Trailer Brake Controller #90195 along with the wiring harness #3063-P is all that is needed to add your controller to your Sprinter with Factory Trailer Plug. Since you are not getting power, you should check fuse F55 which is…

view full answer...

Answer 5

The #8-247-50UC3-EZ and #AKHD-545-35-G-EZ-K will both fit and work with your 13" wheels. These are also compatible with the #40716-15 from your previous question. For the most part it comes down to cost between the two hub/drum assemblies.…

view full answer...

Answer 6

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 7

Instead of using the Hydraulic Brake Kit #AKFBBRK-35-D which requires using 14"-16" wheels you should use the Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly Right #T4423400 and Left #T4423500. These will fit with your…

view full answer...

Answer 8

Your wheels are most likely the 5 on 4-1/2" bolt pattern but the only way to verify is by measuring the hub as they could have been changed in the past 25 years if you are not the original owner. We do have the Westlake ST205/75R14 Radial…

view full answer...

Answer 9

The Kodiak Disc Brakes #KOD69FR will fit on 5,200lb axles which use the #42 spindle dimensions. This is the most commonly used size but depending on the age of your trailer you may want to inspect your spindle. It will have a grease seal landing…

view full answer...

Answer 10

Yes, the Hydrastar EOH drum brake kit part #HBA-10-252-82 does work with Dexter hydraulic drum brakes. Thankfully brake assemblies are all pretty universal with each other so cross compatibility is not an issue.

view full answer...

Does the 7' Kodiak Hydraulic Brake Hose bh-3mfs-7 Come with 45 or 90 Degree Fittings

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching