7-Way and 4-Way Trailer Connection and Step Bumper for 1995 Ford F-350

Question

Question:

I just purchased a 1995 F-350 dully that Im putting a new 16K Curt receiver hitch on. Due to the 10inch bumper the previous owner put on the truck, Im also having to replace the bumper to just a regular step bumper. I will be pulling a lot of different trailers and would like to stay away from adapters as much as possible. Would the above part work on my truck? I know its not what your site recommends, however, this is the type of plug I would like to use. I do have a brake controller in the cab.

asked by: Arlen T

0

Expert Reply:

The Hopkins 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring - Vehicle End # HM40975-11998 will absolutely work on your 1995 Ford F-350. Since you already have a brake controller, the wiring is likely already connected but it not you can find the tow package wires on the rear frame rail.

If you haven't already purchased your step bumper, we have the Westin Fey Surestep Deluxe XLT Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21007-92230 along with other options I've linked.

expert reply by: Jason S

0

Answer 1

The XLT refers to the style of the Westin bumper. I have included a diagram that shows the different bumpers to better illustrate how they are different. Bumper #21007-92230 will fit your 1971 Ford F-100 though you may find that the styling of bumper…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Looks like you have an older version of the 21007-92230 that you referenced which fits the following: 1973 - 1991 Chevrolet C/K Series Pickup 1973 - 1991 GMC C/K Series Pickup 1967 - 1983 Ford F-100, F-150, F-250, F-350 Standard Bed models 1992 -…

view full answer...

7-Way and 4-Way Trailer Connection and Step Bumper for 1995 Ford F-350

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching