Trailer Hitch Recommendation for 2020 Toyota Camry for Carrying Thule Bike Rack

Question

Question:

I have Toyota Camry 2020 XLE and THULE bicycle rack. Can you please recommend a hitch for my car?

asked by: Igor

1

Helpful Expert Reply:

For your 2020 Toyota Camry to carry your Thule bike rack the best hitch option is the Curt part # C11576 which has the best weight capacities of the hitches that fit your vehicle.

I attached an install video for this hitch on a similar 2020 Camry as yours for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

We do have a hitch receiver that is almost completely hidden that is compatible with your 2021 Toyota Camry. The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4", part #C11576, is a Class I hitch receiver that has a maximum tongue…

view full answer...

Answer 2

The Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4 inch and 2 inch Hitches - Frame Mount #TH903202 will work with your class 1 hitch if the distance from the center of the hitch pin hole to the face of the hitch is 1-1/2 inches or greater.…

view full answer...

Answer 3

No, and there will never ever be a 2 inch hitch available for a 2018 Toyota Camry; the only option is indeed the 1-1/4 inch Curt Trailer Hitch #C11576.

view full answer...

Answer 4

The trailer hitch I recommend for your 2018 Camry is the Curt part #C11576. It is a class I hitch that is a confirmed fit for your vehicle and can carry a compatible bike rack with up to two bikes. You just need to make sure that your bike rack fits…

view full answer...

Answer 5

The Curt hitch part #C11257 is a confirmed fit for your 2020 Toyota Camry and your best option for carrying a bike rack. It has plenty of weight capacity for a bike rack too since it's a Class I hitch with a 200 lb tongue weight capacity. For a…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...