Availability of Replacement Spring from Ratchet Repair Kit # DL70475

Question

Question:

Is the replacement spring only available thru your company

asked by: Rich

0

Expert Reply:

Just the spring of the Dutton Lainson Winch Repair kit part # DL70475 is not available. If you needed the spring you'd have to order the entire kit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch…

view full answer...

Answer 2

The Winch Ratchet Repair Kit by Dutton-Lainson #DL70475 (6294) will unfortunately not work with your older Dutton-Lanison 1800 model winch. This repair kit is designed to work with DL1800A, DL1802A, DL2000A, DL2102A, DL2500A, and DL3200A…

view full answer...

Answer 3

We do have several different winch repair kits for Dutton-Lainson hand winches including both a brake spring repair kit #DL5703160 and ratchet repair kits like #DL70475 and the others shown on the linked pages. If you cannot confirm the correct kit…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Availability of Replacement Spring from Ratchet Repair Kit # DL70475

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching