Will Draw-Tite Class II Hitch 36416 Fit a 2008 Toyota Camry SE With Dual Exhaust

Question

Question:

Hi, Could you tell me if this model of trailer hitch is compatible with my car Toyota Camry 2008 SE with dobble tail pipe, one in the right side and other one in the left side? Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4 Item # 36416 I see the image photo but the cars in the photo only have one tail pipe. Thanks

asked by: Edwin O

0

Expert Reply:

The Draw-Tite Class II hitch you refer to, part # 36416 is indeed compatible with a 2008 Camry SE with the Dual Exhausts. I've provided a photo of the hitch once it's installed.

If you'll be towing with the hitch, you'll also need a # 118405 trailer wiring harness, a # 36071 ball mount/hitch pin and for a 1-7/8 inch trailer ball use # 19256 or # 19258 for a 2 inch ball.

I've linked to installation videos for the hitch and the wiring harness.

expert reply by: Mike L

0

click to enlarge

Answer 1

The Draw-Tite trailer hitch #36416, can accommodate a 2010 Toyota Camry with dual exhaust. Take a look at the picture I have included. You can see that the symmetrical design of the hitch leaves enough room for the exhaust on both sides of the…

view full answer...

Answer 2

We offer one hitch for your 2011 Toyota Camry Non-Hybrid SE, part #36416 from Draw-Tite. This is a Class II hitch with a 1-1/4-inch receiver opening. No 2-inch hitches are offered for your 2011 Camry. This is because hitch makers base their hitch…

view full answer...

Answer 3

Based on my research, the 2009 Lexus ES 350 has a towing capacity of 1,000 pounds. I was able to find this information in section 2-5 of the vehicle's online owner's manual. I recommend checking your owner's manual to confirm this…

view full answer...

Answer 4

Yes, the Draw-Tite Trailer Hitch, #36416, will fit your 2007 Toyota Camry SE V6. Installation of this hitch requires drilling and temporary lowering of the exhaust. But if you have the necessary tools and a helping set of hands, you should be able to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...