Length of Shaft on Hitch Ball for Curt Pintle Hook Combo-1-7/8" Diameter - 6,000 lbs - Chrome C44810

Question

Question:

On item Item # C48810 you do not or at least I can not find the length of shaft

asked by: David H

1

Helpful Expert Reply:

The length of the shaft on the Hitch Ball for Curt Pintle Hook Combo - 1-7/8" Diameter - 6,000 lbs - Chrome is 2-3/8" long from the bottom of the ball platform to the bottom of the shaft.

expert reply by: Erik B

1

click to enlarge

Answer 1

I went down to our warehouse and measured the Replacement Hitch Ball for Curt Pintle Hook Combo #C48820. The height of the ball inside the pintle is 2-1/2 inches (see picture). The overall height of the hitch ball is 5 inches.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The diameter of the shank of the #63050 that you referenced is 1-1/8 inches like you said you need. The length of the shank is 2-13/64". You would need to compare that to your pintle to determine if it would fit.

view full answer...

Answer 7

One hundred percent yes, if you are not using weight distribution you can tow your travel trailer using the Rebellion ball mount you asked about: - Curt Rebellion XD Shock Absorbing Adjustable Ball Mount #C57UR The #C57UR will fit your Ram's…

view full answer...

Answer 8

The Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls - 20K #C57UR is going to help dampen the jerking, jarring, bumps, vibrations, chucking, and rattling you may be experiencing but isn't going to evenly…

view full answer...

Answer 9

The internal channel width of the Replacement Shank for Curt Adjustable 2-Ball Mount #C45917 is 3" while the Replacement Ball Platform #C28KR you're looking at has a 2-3/4" width and is for the Curt Rebellion XD rated only for 15K as…

view full answer...

Answer 10

We actually sell a lock set for the ball mount platform of the Curt Rebellion XD #C83WR with the part #IR97FR. The diameter of the pins is 3/4 inch. The usable span of the locks is 2-7/8 inches.

view full answer...

Answer 11

Though we do have the Bearing Buddy #BB2441T-SS that is a direct replacement for Tie Down's Turbo Lube oil baths, this will require you changing over to grease instead of oil. With that said, we do also have the Kodiak XL ProLube Kit…

view full answer...

Answer 12

The diameter of the hole on the platform of the #BWTS35100B is 1-1/4 inch so a 1-7/8 inch hitch ball like the part #C48810 would fit.

view full answer...

Length of Shaft on Hitch Ball for Curt Pintle Hook Combo-1-7/8" Diameter - 6,000 lbs - Chrome C44810

Product Page this Question was Asked From

Continue Researching