Replacement Circuit Board for Atwood Water Heater GC6A-7E

Question

Question:

I have a hot water heater that will not light. It wont even click click click when you try to light it. I have cleaned everything, replaced the thermostats. Do I need to replace the circuit board now, or the whole thing?

asked by: Jeri B

0

Expert Reply:

In order to determine the cause of the problem with the Atwood Water Heater GC6A-7E you will need to have a technician look over the unit and preform the proper diagnostic tests. If the circuit board is bad, we offer the Replacement Control Panel for Atwood Water Heaters part # AT91367 or you can replace the entire unit with the Atwood RV Water Heater part # AT96117.

expert reply by: Jesse M

0

Answer 1

The easiest solution to upgrade your WFCO model WF-8955PEC converter is to use the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp, part #PD4655V. This is a direct replacement for the converter/lower unit, so you would…

view full answer...

Answer 2

I think I found what you're looking for in the Mighty Cord RV Power Cord part #A10-3025ED90 which checks all the boxes that you inquired about. - 30 Amp Service - 25' Length - 90 Degree Twist Lock End If this is not what you wanted then feel…

view full answer...

Answer 3

The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K is a confirmed replacement for your model 7355 that also has the box and circuit breaker panel. If you simply want the converter replacement, then the…

view full answer...

Answer 4

view full answer...

Answer 5

From what I could find out about your current circuit board, the Atwood Replacement Control Panel #AT91367 will be a direct replacement.

view full answer...

Answer 6

There are a couple things to consider. The bolt pattern you are seeking is for a much smaller axle so there are not hubs compatible with the spindles you have and that bolt pattern. The fit we have for the measurements you gave are only the 8 on…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Replacement Circuit Board for Atwood Water Heater GC6A-7E

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching