Foot Plate or Wheel Options for etrailer A-Frame Jack TJA-5000-B

Question

Question:

Is there a leg available that will fit this jack?

asked by: Mike

0

Expert Reply:

For the etrailer a-frame jack part # TJA-5000-B we have the detachable foot plate part # JF-99 as one option or we have a caster wheel part # JC-102 as another option!

expert reply by: Jameson C

0

Answer 1

All of the side mount jacks that we carry either come with a welded footplate or welded wheel. Though the tubing size is 2 inches, I cannot recommend modifying jack #DL22300, or any jack with a wheel or footplate welded on, as it will void the…

view full answer...

Answer 2

The drop leg #JF-1005H-Z fits 2,000 pound etrailer and Ram jacks as well as topwind 5,000 pound jacks, like part #TJA-5000-B but it doesn't fit the 5,000 pound sidewind jacks like #TJA-5000S-B. The inner tube on the 5k sidewind jacks have a…

view full answer...

Answer 3

The Round A-Frame Trailer Jack #TJA-5000-B you were looking at does not have grease zerks, nor is it greaseable. This is the same for all of the top wind A-Frame jacks we offer. The reason for this is A-Frame jacks like this are sealed to keep debris…

view full answer...

Answer 4

If you look at the backs of the brake assemblies there should be a hole where the magnet wires come out and a little opaque plastic strap. So if you are looking at the back of the assembly and those items are on the left then it is the left side…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Foot Plate or Wheel Options for etrailer A-Frame Jack TJA-5000-B

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching