Replacement Lock Cylinder for Extang Encore on 2014 Chevy Silverado 1500

Question

Question:

i need replacement lock for xtang encore for 2014 silverado ltz, numbers by lock are 62445 14149

asked by: Frank R

0

Expert Reply:

Since the truck is a 2014 Chevy Silverado 1500 the correct Extang Encore lock core replacement is the part # EX28620162-28.

expert reply by: Jameson C

0

Answer 1

The Replacement Tarp #EX92405-20 is for a Extang Trifecta 2.0 Soft Tonneau Cover #EX92405 that fits a 2009 - 2014 Ford F-150 5-1/2 Foot Bed. To properly identify the correct replacement cover you will need to locate the part number on the tonneau.…

view full answer...

Answer 2

We don't carry the Undercover brand tonneau cover but I can tell you that the lock core on the #EX28620162-28 is roughly 1-1/2" in diameter. If the lock core opening is that diameter this would work well for you.

view full answer...

Answer 3

According to Pop & Lock you will want to use their Power Pop Remote Keyless Entry Kit for Hard Tonneau Covers #PAL9000 with your UnderCover tonneau cover. This will replace the standard latches with actuating rotary latches that unlock and open…

view full answer...

Answer 4

I went out to the warehouse and measured the Replacement OEM BOLT Lock for Extang EnCore Hard Tonneau Cover 28620192-28 and measured 2" across on the top, but the bottom part that would actually go into the tonneau cover measured 1-3/8" in…

view full answer...

Answer 5

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Replacement Lock Cylinder for Extang Encore on 2014 Chevy Silverado 1500

Continue Researching