Hitch and Swinging Bike Rack Recommendation for 2020 Honda Odyssey

Question

Question:

Can the tilting bike rack tilt while bikes are loaded. have a 2020 honda odyesse. I need access to open trunk space while rack is attached. is the swing sway better? I also need a hitch.

asked by: Reggie L

0

Expert Reply:

Tilting Bike Racks like the Thule Camber # TH9058 would need to have the bikes removed before the rack can be tilted rearward, because the bikes would hit the ground and not only damage them but would also prevent the rack from fully tilting down. This is definitely not the most convenient thing if you need to be constantly in and out of the cargo area of your Odyssey.

I'd recommend a swinging bike rack like the USA manufactured SportRack Ridge Swing # SR2415. This rack would allow full access to the cargo area of your Odyssey by swinging up to 180° to the passenger side and allowing the rear hatch to open while up to 4 bikes are still on the rack.

For a hitch, I prefer the concealed look of the Curt # C64NR. The hitch crossbar is hidden behind the bumper cover, so all that's visible is the receiver tube and the safety chain hooks. This definitely provides a much better appearance, but the installation is more involved, and the hitch is more expensive. If you're not as concerned about how the hitch appears on the vehicle, I'd recommend the Curt # C13370 because of its much simpler installation and lower cost.

I've linked to a product demonstration video for the bike rack I recommended, as well as to install videos for both hitches. The videos will show you exactly what the hitches look like once installed, which should help you decide between the two.

expert reply by: Mike L

0

Answer 1

The EcoHitch #306-X7372 and the Curt #C64NR both have identical weight capacities (3500 lbs towing/525 lbs tongue weight), would install in the same manner, would be visually very similar and the receiver tubes would sit at the same spot in relation…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

The Curt Trailer Hitch #C12289 will in fact, fit your 2005 Dodge Caravan SE. The hitch will not interfere with any of the vans VMI modifications as it does not get close enough to the rear axle. Additionally, when the hitch it fully installed it is…

view full answer...

Answer 11

We can definitely get you all the parts needed to add brakes to your trailer, but it is going to be an extensive list since there currently isn't anything on the axle. I did include an article regarding just this kind of situation, but lets get…

view full answer...