Trailer Hitch for 2002 Chevy Silverado 2500 LD That Doesn't Attach To Bumper

Question

Question:

Looking for a hitch that does not attach to my bumper On 2002 light duty 3/4 chev silverado. Bumper supports rusted out.

asked by: Rick L

0

Expert Reply:

The Curt # C15323 installs to the underside of the frame members as shown in the provided diagram.

You'll want to make sure the rear frame members where the hitch would install are still sound. Some surface rust is normal, but if it's any worse than that I wouldn't recommend towing with that vehicle.

I've linked to an install video that you might find helpful.

expert reply by: Mike L

0

Answer 1

According to Draw-Tite, their Class IV receiver hitch part #41932 is indeed a fit for the 2000 GMC Sierra 2500LD truck, as long as your truck has the OEM bumper and brackets. To see installation details, click the provided link.

view full answer...

Answer 2

The 2 bolts that go into the bumper portion of the Curt Trailer Hitch Receiver #C14332 are a required part of the installation. Curt will void any warranty on the hitch if it is not installed properly as per their instructions. There is no way to…

view full answer...

Answer 3

According to the owners manual for your 2004 GMC Sierra 1500 4x4 extended cab with the automatic transmission it carries either a maximum trailer weight of 7,800lbs or 8,800lbs depending on the axle gear ratio. If you have 3.73 gears it is rated for…

view full answer...

Answer 4

The Curt Class V Hitch part #C15323 that you referenced has been confirmed by Curt to fit your 2012 Chevy Silverado 1500 4x4, crew cab, short bed truck. This hitch should work well for you. I attached installation instructions for you to check out.…

view full answer...

Answer 5

The hitch you need depends on the bumper you have now on your 2005 GMC Sierra 2500. The Curt #C15312 is designed to fit if your truck has the factory cutout bumper. More than likely this is what you have on your truck. The #C15313 is designed for…

view full answer...

Answer 6

Hi Richard! It sounds like you're needing to install the Load Resistor Kit for LED Turn Signals #DI34ZR on the turn signals you've installed on your toolbox. Since LEDs don't require as much power as incandescent bulbs, sometimes we see…

view full answer...

Answer 7

Electric brakes have 2 wires located at the back. One is for power and the other is for ground (it doesn't matter which is used for which function). The ground wires should be connected to the trailer frame. The only other place that would carry…

view full answer...

Answer 8

There is a Class V hitch that fits your 2002 Chevy Silverado 1500 HD, though I checked with B&W, and the B&W hitch is not a fit for your truck. Instead, the Class V hitch that does fit is from Curt: - Curt Trailer Hitch Receiver #C15323 I…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes! I went ahead and attached the installation instructions of the Demco Underbed Rail and Installation Kit #DM8551004 (Demco part 8551004) to this answer.

view full answer...

Trailer Hitch for 2002 Chevy Silverado 2500 LD That Doesn't Attach To Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching