Recommended Valve Stem Extenders for Dual Rear Wheels On Chevy Express Chassis

Question

Question:

2014 chevrolet express 4500 dually, i need the valve stem extension that is steel braided for an inside rear wheel..i think it has a bracket with it

asked by: Dan

0

Expert Reply:

If you are looking for valve stem extenders to use on a set of dual rear wheels we have plenty of options, the Wheel Masters 4-Hose Inflation Kit part # WM8001 which comes with mounting brackets is what I recommend. That said, none of which will be specific to any one particular application so if the above will not work you'll need to take a look at the selection I have attached below.

expert reply by: Conner L

0

Answer 1

Absolutely, and there are two Reese M5 fifth wheel hitches that fit the OEM puck system in your 2022 GMC Sierra 3500HD, with the only difference being their capacities: - 20,000 lb Capacity: Reese M5 5th Wheel Trailer Hitch for Chevy/GMC Towing Prep…

view full answer...

Answer 2

What is the distance between the mounting holes on that light? If they are 1-3/4 inches apart on center the part #MCL14AB will fit and use the exact same holes. Since this light has the same length as yours at 2-1/2 inches and the mounting holes look…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The Viair EVC Battery Powered Tire Inflator #VA88JR weighs only about 2 lbs. The compressor itself (not including the hose) is 6-1/4" tall x 2-3/4" wide x 1-7/8" deep. I have attached a dimensional drawing below for your reference.…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...