Are the Bearing Buddy Bearing Protectors BB2717 Threaded

Question

Question:

Model 2717 - Chrome Plated Pair ... want to note whether you hubs are threaded or non-threaded as we offer both types of Bearing Buddy. I have ones that are threaded, i cant find the part number for the threaded ones

asked by: Chris K

0

Expert Reply:

The Bearing Buddy Bearing Protectors part # BB2717 are not threaded, they instead offer press-in installation. There are Bearing Buddy Bearing Protectors available which are threaded but not for a 2.717" bore. I have attached a full list of options below but you will need to verify the exact hub bore down to the thousandth of an inch to confirm.

expert reply by: Conner L

0

Answer 1

Bearing Buddy pumps grease into the center of the hub all the way back to the grease seal. A double lip seal should be used to prevent grease from blowing out the seal when added. When the hub and seals and bearings are first assembled, they should…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 6

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 11

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 12

I looked up the information on your TDE 46205 Hubs and found a couple of great replacements for you. The one you pick will depend on the number of wheel studs you have. For 5 wheel studs use the etrailer Trailer Idler Hub Assembly for 2,000-lb E-Z…

view full answer...